亚洲免费av电影一区二区三区,日韩爱爱视频,51精品视频一区二区三区,91视频爱爱,日韩欧美在线播放视频,中文字幕少妇AV,亚洲电影中文字幕,久久久久亚洲av成人网址,久久综合视频网站,国产在线不卡免费播放

        ?

        Simulation of multi-modal control in electro-hydraulicposition servo-system*

        2014-09-05 05:47:40GuoqingZHOU
        機床與液壓 2014年6期
        關鍵詞:仿人動態控制伺服系統

        Guo-qing ZHOU

        School of Architecture and Materials,Chongqing College of Electronic Engineering,Chongqing 401331,China

        Simulationofmulti-modalcontrolinelectro-hydraulicpositionservo-system*

        Guo-qing ZHOU?

        SchoolofArchitectureandMaterials,ChongqingCollegeofElectronicEngineering,Chongqing401331,China

        Aiming at the characteristic of parameter time-varying,nonlinearity etc in electro-hydraulic position servo-system caused by oil spill,oil pollution,inert zone and hysteresis,the paper explored the multi-modal control strategy based on human simulated intelligent control.In the paper,it analyzed the open question of electro-hydraulic position servo-system,discussed the essential feature of human simulated intelligent control,summarized up the characteristic of multi-modal control and its corresponding control algorithm.The comparative study of simulation experiment in multi-modal control and PID control verified the good control quality of multi-modal control.The simulation results demonstrated that compared with PID control by means of multi-modal control it could obtain better tracking performance,static and dynamic characteristics as well as stronger robustness than PID control.

        Electro-hydraulic position servo-system,Human simulated intelligent control,Multi-modal control

        1.Introduction

        The hydraulic servo system has been widely used for the industrial automation field resulted in lots of priority such as being big in moment etc.But there are improper phenomena in the hydraulic servo system such as oil leakage,oil pollution,dead zone and hysteresis as well as flow rate nonlinearity of valve control mechanism etc,and it makes the ubiquity of low control accuracy resulted by the characteristic in time-varying parameter and nonlinearity etc,therefore there are lots of practical problem needed to be solved.Many scholars have made effectively discussion and contributors.The reference[1] researched on control of electro-hydraulic serve position system from the control angle of fuzzy immune adaptive PID control,reference[2]explored the control of nonlinear electro-hydraulic position servo system from PID iterative learning control,reference[3] studied the fuzzy PID control of hydraulic position servo system,and reference[4-6] also researched on electro-hydraulic serve position system control from different angle,but all they are the control based on PID and its improved PID control.In fact,the control of electro-hydraulic serve position system is to indicate the control that can accurately reproduce or follow a process of controlled variable such as mechanical displacement etc.Due to some uncertainty factors resulted by time-varying parameters,cross coupling and nonlinearity etc,it is difficult to make the precise mathematical modeling,and therefore it is hard to deal with the impact of uncertain factors on the system by means of the control based on PID and its improved PID controller.This paper makes some discussion for related problems from the angle of multi-modal control in human simulated intelligent controller (HSIC).

        2.Substantive characteristics of HSIC

        Aiming at being less than satisfactory in tracking performance etc which is resulted in many uncertain factors of electro-hydraulic position servo system,the control strategy of HSIC is a reasonable choice[7-8].Faced on the challenges,the intuitive way of intelligent control is to seek the answer from one's own.Based on the theory of artificial intelligence and automatic control,HSIC sums up the experience of human control,and it can adopt the production rules to describe the inspiration and intuition reasoning as well as control behavior.From control theory point of view,it can describe the intuitive reasoning by means of production rules,and based on online characteristic recognition and memory it can be sum up the motion dynamic characteristic model.By means of the principle combined open and closed loop,it can implement the multi-modal control of combined qualitative decision and quantitative control.HSIC showed the following characteristics in the structure and function.The information processing and decision-making mechanism are related to the interested hierarchy,namely the information processing and decision-making mechanism of different hierarchy are different,and it is hierarchical.The characteristic recognition and characteristic memory can be online for the system with the help of the system error and its rate of change.Based on the fusion each other of open-closed loop control and quantitative as well as qualitative decision,it can actualize the multi-modal control strategy.The logic of reasoning can use heuristics and intuition in reasoning.The basic concept of HSIC is to simulate the control functions of human beings.The generalized control model of solving control problem is shown in Figure 1.

        Figure 1.Generalized control model

        3.Design of controller

        The prototype algorithm based on HSIC is the following.

        Figure 2.Algorithm static characteristic

        From Figure 2 it can be seen that if it deviates the balance state zero,when the error increases gradually it takes proportional control until when the error reaches the position of an extremum the control amount runs up to the maximum.After that,the error has decreasing trend it can maintain control mode,and it makes observation and waiting for error change.If error increases towards to opposite direction,then it still adopts the proportional control and repeats the same process control roughly.After through the switching process like “proportion-holding-proportion-holding”,the system would be quickly stabilized at the new balance point.The above is the solving process for objective control amount.At the same time of switching holding and proportion modal,the control amount also is continuously modified until the system is stabilized to setting value,and the control amount is stabilized to objective control amount.Of course,if the setting value ofKpandkis different,it would bring the impact for solving process.So long as the setting value ofKpandkis proper,it can fast obtain the target control amount.

        3.1.Designprocedure

        1) Determine the design target trajectory

        2) Establish the characteristic model

        Φi=P⊙Qi,i=1,2,3,…

        3) Control modal set and control rule

        According to the system deviation and its change trend it designs the control or correction modal,and the control modal set and control rule is the surjective relation of one to one correspondence.It can constitute the control rule through determining control volume and threshold adjustment etc.

        3.2.Designofcontrolalgorithm

        The characteristic model is shown in Figure 3.In which,the horizontal ordinate shows the error of system,and the vertical coordinate shows the error change rate.The target of controller design is to make that the actual is consistent with the ideal error target trajectory as far as possible,and the dotted line in Figure 3 is as the ideal error target trajectory.

        Figure 3.Control characteristic model

        Aimed at different region located by system state,it should take different control strategy.Corresponding to region ①,due to the deviation large,it takes Bang-Bang control so as to reduce the deviation rapidly.Corresponding to region ②,due to the deviation change rate being not greater than the predetermined value and the deviation being reduced,it takes proportional modal control.Corresponding to region ③ and region ⑥,it takes proportional plus differential modal control.Since the deviation increases or decreases and the deviation change rate is greater than the predetermined value,and after joining the differential control it can control the deviation change rate.Corresponding to region ④,it can take the control of positive feedback proportional differential modal because of control deviation being reduced and its change rate still being not be able to reduce to predetermined value.Corresponding to region ⑤,all the system deviation and its change rate satisfy the system demand,and it takes proportional plus integral control so as to eliminate the static error.According to the above control strategy,the control algorithm can be summarized as follows.

        4.Simulation experiment

        In order to simplify the analysis and not to lose the generality,it takes one order inertia object with lag as the simulation model in the paper.The impact such as parameter time-varying,nonlinearity etc can be equivalent to the change such as lag,system parameter change and external disturbance etc.Then it examines the robustness of the system,so long as the control algorithm is strong in robustness,then the control strategy is advisable.It assumes the model to be asW(S)=Ke-τs/ (TS+1),and in whichKis the gain coefficient,Tis the time constant of controlled object andτis the pure lag,and then it takes respectivelyK=1,T=1.2,τ=2,after replacing the simulation is asW(S)=e-2S/(1.2S+1).

        Based on Matlab environment,by means of Simulink it can construct the simulation model of system.Under the condition of unit step input,it can make the simulation for the same controlled object respectively adopting PID control and multi-modal control.Figure 4 shows the comparison of response curve for two sorts of control algorithm.From the analysis of curve 1 and curve 2 it can be seen that both curve 1 and curve 2 are not any overshoot,but the multi-modal control owns better performance index in the rise and adjusting time.

        Figure 4.Comparison between response curves

        Figure 5 shows the comparison of response curve for two sorts of control algorithm,and in which,it makes simulation under the condition of joining an external pulse disturbance at timet=4.5 s.From the comparison of response curve it can be seen that the multi-modal control owns stronger anti-jamming performance than PID control.

        Figure 5.Comparison of response in disturbance

        Figure 6 shows the comparison of response curve for two sorts of control algorithm,and in which the difference is that the original object is joined by an inertial node,namely the transfer functionW(S)=e-2S/(1.2S+1) is transformed ase-2S/(1.2S+1)(2S+1).Through the comparison of curve 1 and curve 2,it can be seen that the overshoot of PID control is greatly increased,and it gets longer in the rise and adjusting time,but the response curve is hardly changed by multi-modal control,and therefore it shows that the parameter change hardly influences system response.

        The above simulation experiment shows that the multi-modal control strategy can obtain more ideal dynamic and static performance index for whatever parameter change or external disturbance,and by means of multi-modal control it can get better control quality than PID control.

        Figure 6.Comparison of parameter change impact

        5.Conclusion

        In the multi-modal control,after each control step it must actualize the control pattern recognition according to characteristic model,and then by means of recognition result it selects the control algorithm so as to modify the system state.Therefore it can ensure the control quality of system,and implement effective control for electro-hydraulic position servo-system,and obtain better tracking performance.

        [1]ZHU Bao,WU Rong-zhen,XONG Rui-ping,et al.Research for the fuzzy-immune-PID control of the electro-hydraulic servo system[J].CHINA MEASUREMENT TECHNOLOGY,2004(1): 19-21.

        [2]Cao Shuping,Luo Xiaohui,Zhang Hanwen,et al.PID-type Iterative Learning Control for Nonlinear Electro hydraulic Positional Servo-system[J].Mechanical Science and Technology for Aerospace Engineering,2008,27(1): 19-22.

        [3]XU Jian.Study on Fuzzy PID Control for Hydraulic Position Servo System[J].Automation Panorama,2008(4):66-68.

        [4]SUN De,LE Guigao,ZHUANG Wenxu.Rocket Position Servo-system Control with Composite PID[J].Journal of Projectiles,Rockets,Missiles and Guidance,2012,32(1): 215-218.

        [5]JIANG Yi,YU Junqi,KIU Xi.Fuzzy Self-tuning PID Control Algorithm of Position for MTS Hydraulic Servo System[J].Industrial Control Computer,2010,23(12): 58-60.

        [6]GAO Zilong,LI Zhigang.Research of Position Servo Systems Based on Fuzzy Controller[J].MICROMOTORS,2013,46(1):67-71.

        [7]LI Zu-shu,TU Ya-qing.Human Simulated Intelligent Controller[M].Beijing: National Defence Industrial Press,2003.

        [8]Li Shi-yong.Fuzzy Control Neural Control and Intelligent Cybernetics.Harbin: Harbin Industry University Press,1998.

        多模態控制在電液位置伺服系統中的仿真研究*

        周國清?

        重慶電子工程職業學院 建筑與材料學院,重慶 401331

        針對漏油、油液污染、死區、滯環等因素導致的液壓伺服位置系統的參數時變、非線性等特性,探討了基于仿人智能的多模態控制策略。分析了液壓伺服位置控制存在的問題,討論了仿人智能控制的本質特征,動態控制特征模型,總結了控制的多模態特性及其相應的控制算法。多模態控制與PID控制的仿真實驗對比研究驗證了多模態控制具有良好的控制品質。仿真結果表明:與PID控制相比較,采用多模態控制時電液位置伺服系統可獲得更好的跟蹤性能、動靜態特性以及更強的魯棒性。

        電液位置伺服系統;仿人智能控制;多模態控制

        TP273

        2013-11-24

        *Project supported by Chongqing Education Commission (2012-09-3-314)

        ? Guo-qing ZHOU: Associate professor.E-mail: 24896300@qq.com

        10.3969/j.issn.1001-3881.2014.06.022

        猜你喜歡
        仿人動態控制伺服系統
        北京航空航天大學學報(2022年6期)2022-07-02 01:59:46
        基于全過程動態控制下的建筑工程進度管理研究
        探究施工階段工程造價動態控制的方法與策略
        建筑工程造價特點及動態控制實施方法探討
        基于復合前饋模糊PID的位置伺服系統研究
        異構遙操作仿人機械臂靈巧作業控制
        工程施工階段造價動態控制研究
        探究仿人機器人設計及步行控制方法
        基于自適應反步的DGMSCMG框架伺服系統控制方法
        具有面部表情的仿人頭部機器人系統的研制
        精品三级av无码一区| 国产精品高清免费在线| 国产成人大片在线播放| 久久久久亚洲精品无码蜜桃| 成 人 网 站 免 费 av | 漂亮的小少妇诱惑内射系列| 美女免费观看一区二区三区| av色综合久久天堂av色综合在 | 日本熟妇人妻xxxx| 中文人妻av久久人妻18| 国产精品白浆视频一区| 日本女优五十路中文字幕| 伊人久久精品无码二区麻豆| 装睡被陌生人摸出水好爽| 特级毛片全部免费播放a一级| 杨幂一区二区系列在线| 精品国产av一区二区三区| 欧美午夜刺激影院| 亚洲国产一区二区三区视频在线| 白浆国产精品一区二区| 熟女无套内射线观56| 亚洲av无码成人网站www| 中文字幕在线久热精品| 97超碰中文字幕久久| 免费无码专区毛片高潮喷水| 天天摸日日摸狠狠添| yy111111少妇影院| 亚洲最大一区二区在线观看 | 国产无套护士在线观看| 成激情人妻视频| 日本黑人乱偷人妻在线播放| 成人无码α片在线观看不卡| 亚洲免费av电影一区二区三区| 美女把内衣内裤脱了给男人舔| 亚洲精品成人无限看| 抽搐一进一出试看60秒体验区 | 97人妻精品一区二区三区免费 | 久草手机视频在线观看| 亚洲一区 日韩精品 中文字幕 | 国产亚洲av看码精品永久| 永久免费看啪啪网址入口|