岑學齊, 吳曉東, 王 磊, 鄭 磊, 葛 磊
(石油工程教育部重點實驗室(中國石油大學(北京)), 北京 102249)
?
?油氣開發?
游梁式抽油機游梁平衡重計算新模型
岑學齊, 吳曉東, 王磊, 鄭磊, 葛磊
(石油工程教育部重點實驗室(中國石油大學(北京)), 北京 102249)
摘要:為了精確計算游梁式抽油機游梁平衡重的調整量,保障游梁式抽油機安全節能運行,需要對游梁式抽油機的調平衡模型進行研究。分析了游梁式抽油機急回運動特性,得出了抽油機上下沖程所用時間可能不相等的結論,并建立了游梁平衡抽油機上下沖程電機平均輸出功率的計算公式。在此基礎上,依據抽油機上下沖程電機所做功相等的平衡準則,利用平衡重平均功率變化與電機功率變化的關系,推導出了功率曲線法游梁平衡重計算新模型。實例計算表明:應用新模型對平衡重進行調整后,上下沖程電機做功差值很小,更能滿足上下沖程電機做功相等的平衡準則要求;抽油機上沖程運行時間越長,平衡重調整量越大,而下沖程運行時間越長,平衡重調整量越?。划?dāng)上下沖程運行時間接近時,新模型和簡化模型計算結果接近。這表明,對于上下沖程運行時間不相等的游梁式抽油機,利用功率曲線法游梁平衡重計算新模型調整平衡重,抽油機平衡狀況更佳。
關鍵詞:游梁式抽油機;游梁平衡重;輸出功率;數學模型
節能降耗,降低生產成本,對于提高油田經濟效益有重要的作用,而圍繞抽油機平衡尋找節能降耗切入點,可以提高抽油機系統效率。游梁式抽油機調平衡是采油生產管理工作中一項重要的內容,關系到抽油機是否安全節能運行[1-2][3]100。游梁式抽油機調平衡的方法主要有電流法、功圖扭矩法和功率曲線法。電流法和功圖扭矩法在現場應用普遍,但隨著功率曲線測試的普及,利用功率曲線調平衡的方法越來越受到關注。功率曲線調平衡的方法也為解決抽油機能耗高、系統效率低、“大馬拉小車”的問題提供了新途徑。
中國石油天然氣集團公司企業標準《游梁式抽油機平衡及操作規范》(Q/SY 1233—2009)中,以上下沖程中平均功率相等為平衡準則,推導出利用功率曲線法求解游梁平衡抽油機游梁平衡重調整量的公式,推導該公式時假設上下沖程時間相等,但在實際生產中,抽油機上下沖程運行時間并不一定相等。為此,有必要考慮上下沖程運行時間不一定相等的情況,確定上下沖程目標平均功率,利用平衡重的平均平衡功率變化與電機功率變化的關系[1,4-5],推導游梁平衡重調整量計算新模型,以提高平衡重調整量的計算精度,確保游梁式抽油機安全節能運行。
1平均功率的計算
1.1游梁式抽油機急回特性
在游梁式抽油機四連桿機構中(見圖1),當抽油機曲柄OC做勻角速度圓周運動時,抽油機游梁O′A則在O′A′與O′A″之間做往復運動。曲柄在OC′和OC″兩個極限位置時所夾銳角θ為極位夾角。
圖1 抽油機運動示意Fig.1 Movement schematic of pumping units
當游梁式抽油機曲柄做勻角速度運行時,抽油機上下沖程運行的時間分別為:
(1)
(2)
式中:tu和td分別為抽油機上下沖程運行時間,s;φ1和φ2分別為抽油機上下沖程曲柄旋轉的角度,rad;ω為曲柄角速度,rad/s。
由圖1可知,φ1=π+θ,φ2=π-θ。
從圖1還可以看出,抽油機上下沖程運行時間與抽油機的曲柄旋向、抽油機極位夾角有關。假設圖1中的曲柄順時針旋轉時,則存在以下關系:
當I=B時,極位夾角θ=0,φ1=φ2,tu=td;
當I>B時,極位夾角θ為正,φ1>φ2,tu>td;
當I
其中,I為游梁軸中心到曲柄軸中心的水平距離,m;B為懸點處在上、下死點時連桿和游梁軸的結合點到游梁軸中心的水平距離,m。
目前國內使用的常規游梁式抽油機主要采用極位夾角為正的偏移四連桿機構[5-7],具有急回運動特性,即上沖程慢,下沖程快[5],因此將上下沖程運行時間默認為相等是不符合實際生產情況的。
1.2上下沖程電機平均輸出功率計算式
(3)
(4)
文獻[4]給出了未考慮上下沖程運行時間不相等情況的上下沖程電機平均輸出功率的計算式:
(5)
(6)
2游梁平衡重計算新模型
判斷抽油機是否實現理想平衡的依據主要有以下3個[2][3]117-130:1)抽油機上下沖程電機對外做功相等;2)上下沖程減速箱曲柄軸峰值扭矩相等;3)整個沖程中減速箱曲柄軸扭矩均方根值最小。
依據抽油機上下沖程電機所做功相等的平衡準則,考慮上下沖程時間不一定相等的情況,結合平均功率的定義,計算上下沖程調平衡的目標平均功率:
(7)
(8)
為達到目標平均功率,上下沖程電機平均輸出功率調整值分別為:
(9)
(10)
(11)
(12)
游梁平衡重依靠重力做功,調整游梁平衡重的重量,平衡重的平均平衡功率也隨之改變。上下沖程中,平衡重平均平衡功率的變化與電機平均輸出功率的變化存在以下關系[2,7-14]。
(13)
(14)
結合式(9)—(14),可得:
(15)
式中:η1為皮帶效率;η2為減速箱效率;η3為四連桿效率。
根據抽油機的幾何關系(如圖2所示),Hy的計算公式為[4-7]:
(16)
圖2 游梁平衡抽油機的幾何關系Fig.2 Geometric relationship of beam-balanced pumping units
式中:c為抽油機平衡臂的長度,m;a為抽油機前臂的長度,m;S為抽油機沖程,m;γ為游梁平衡角(下偏角),rad。
將式(16)代入式(15)中,推導出平衡重調整量的計算新模型為:
(17)
當ΔGy為正時,表示要增加游梁平衡塊的重量;當ΔGy為負時,表示要減少游梁平衡塊的重量[15-21]。
該方法假設條件是曲柄勻角速度運轉,故該模型不適合于變頻調速電機驅動的游梁式抽油機。
3計算實例及結果分析
已知參數:抽油機前臂長5.5 m,抽油機平衡臂長3.162 m,游梁平衡角0.157 rad,光桿沖程6 m,沖次4 min-1,上沖程時間8.5 s,下沖程時間6.5 s。皮帶效率η1為90%,減速箱效率η2為90%,四連桿效率η3為95%。電機輸出功率曲線如圖3所示。
3.1新模型與簡化模型調平衡效果對比
按照新模型計算得到ΔGy為3.640 kN。按照簡化模型(式(18))計算得到ΔGy為2.250 kN。利用平衡重調整量與電機輸出功率變化量的對應關系[2],分別按新模型和簡化模型計算出的調整量計算電機輸出功率曲線,結果見圖3。根據圖3中的電機輸出功率曲線,利用上文公式就可計算按照不同模型調整后上下沖程的平均功率和電機所做的功,結果見表1。
圖3 電機輸出功率曲線Fig.3 Motor output power curve
Table 1Average output power and work of motors before and after the balance adjustment
沖程平均輸出功率/kW電機做功/kJ調平衡前新模型簡化模型調平衡前新模型簡化模型上沖程7.0425.1455.87059.86143.73449.894下沖程4.5236.1016.05129.40145.46839.331
由表1可知:游梁平衡重調整前后,整個沖程電機做功基本不變,均約為89.2 kJ;應用新模型調整平衡重后,上下沖程電機做功差值由30.460 kJ減小為1.734 kJ;應用簡化模型調整平衡重后,上下沖程電機做功差值由30.460 kJ減小為10.563 kJ。此外,應用新模型調整平衡重后,上下沖程峰值功率相差1.192 kJ,而應用簡化模型調整平衡重后,對應差值為1.409 kJ,由此可見,按照新模型調整平衡重后的上下沖程中峰值功率更接近(見表2)。
表2調平衡前后峰值功率對比
Table 2Peak power contrast before and after the balance adjustment
條件上沖程峰值功率/kW下沖程峰值功率/kW上下沖程峰值功率差/kW調平衡前14.1878.5685.618簡化模型12.41411.0051.410新模型11.31912.511-1.192
3.2平衡重調整量與上下沖程運行時間的關系
假設抽油機整個沖程運行時間是15 s不變,應用新模型分析抽油機上下沖程運行時間對平衡重調整量的影響,結果見圖4。
圖4 平衡重調整量與抽油機上下沖程運行時間的關系Fig.4 The relationship between the counterbalance weight adjustment and the upstroke/downstroke time of pumping units
從圖4可以看出:抽油機上沖程運行時間越長,平衡重調整量越大;下沖程運行時間越長,平衡重調整量越小。由于簡化模型認為上下沖程運行時間相等,因此當上下沖程運行時間接近7.5 s時,新模型計算結果接近簡化模型。
4結論
1) 根據抽油機結構及運動規律,以及抽油機上下沖程運行時間與曲柄轉角的關系,得出了抽油機上下沖程運行時間可能不相等的結論,并在此基礎上建立了上下沖程電機平均輸出功率計算公式。
2) 考慮抽油機上下沖程運行時間不相等的情況,以假設上下沖程電機所做功相等為準則,建立了利用平均功率計算游梁平衡重調整量的新模型。
3) 計算表明,與假設上下沖程運行時間相等的簡化模型相比,應用考慮上下沖程運行時間不相等的新模型調整平衡重后,抽油機平衡狀況更佳。
參考文獻
References
[1]郝世彥,樊平天,張新濤.油井遠程監控與計量技術在延長油田的應用[J].石油鉆探技術,2010,38(2):84-87.
HAO Shiyan,F(xiàn)AN Pingtian,ZHANG Xintao.Application of remote well monitoring and measurement technique in Yanchang Oilfield[J].Petroleum Drilling Techniques,2010,38(2):84-87.
[2]吳曉東,岑學齊,安永生,等.基于平均功率法的游梁式抽油機功率曲線法調平衡模型[J].石油鉆采工藝,2015,37(2):63-66.
WU Xiaodong,CEN Xueqi,AN Yongsheng,et al.Balance adjusting model by power curve of beam-pumping unit based on average power method[J].Oil Drilling & Production Technology,2015,37(2):63-66.
[3]張琪.采油工程原理與設計[M].東營:石油大學出版社,2000:100,117-130.
ZHANG Qi.Theory and design of oil production engineering[M].Dongying:Petroleum University Press,2000:100,117-130.
[4]Q/SY1233—2009游梁式抽油機平衡及操作規范[S].
Q/SY1233—2009The operation and balance for beam-pumping units[S].
[5]韓冬.抽油機極位夾角、旋向與能耗關系研究[J].石油石化節能,2012,2(3):9-10.
HAN Dong.Study on the relationship between limit position angle of pumping unit,direction of rotation and energy consumption[J].Energy Conservation in Petroleum & Petrochemical Industry,2012,2(3):9-10.
[6]黃偉,甘慶明,張磊,等.基于電參數的螺桿泵桿管偏磨預判研究[J].石油鉆探技術,2014,42(4):102-106.
HUANG Wei,GAN Qingming,ZHANG Lei,et al.Prejudgment of eccentric wear of screw pump rod based on electrical parameters[J].Petroleum Drilling Techniques,2014,42(4):102-106.
[7]王懷奧,周欣.急回四桿機構綜合綜述[J].佳木斯大學學報(自然科學版),2005,23(2):297-300.
WANG Huaiao,ZHOU Xin.An overview of synthesis on quick-return four-bar machinery[J].Journal of Jiamusi University(Natural Science Edition),2005,23(2):297-300.
[8]中國石油天然氣總公司勞資局.采油工程[M].2版.北京:石油工業出版社,1996:99-103.
The Labor Bureau of China National Petroleum Corporation.Oil extraction engineering[M].2nd ed.Beijing:Petroleum Industry Press,1996:99-103.
[9]孫延安.游梁式抽油機合理平衡判別方法研究[J].石油機械,2014,42(3):72-75.
SUN Yan’an.Research on the reasonable balance discrimination method for beam pumping unit[J].China Petroleum Machinery,2014,42(3):72-75.
[10]張明亮,雷長森,田小蘭,等.抽油機曲柄平衡的調整計算及效果預測[J].石油機械,2001,29(5):36-39.
ZHANG Mingliang,LEI Changsen,TIAN Xiaolan,et al.Balance adjustment and calculation of pumping unit with crank[J].China Petroleum Machinery,2001,29(5):36-39.
[11]顧永強,周靜,李玲,等.改進抽油機井“功率平衡”測試實現節能降耗[J].油氣田環境保護,2009,19(4):45-47.
GU Yongqiang,ZHOU Jing,LI Ling,et al.Energy saving test on “power balance” of improved pumping well[J].Environmental Protection of Oil & Gas Fields,2009,19(4):45-47.
[12]周繼德.用功率曲線法判斷和調整抽油機的平衡[J].石油礦場機械,1988,12(5):7-9.
ZHOU Jide.Adjustment of counter balance of pumping unit by using electric power characteristics[J].Oil Field Equipment,1988,12(5):7-9.
[13]侯立功,劉超,陶明.雙驢頭抽油機平衡調整的簡易方法[J].油氣田地面工程,2008,27(7):52-53.
HOU Ligong,LIU Chao,TAO Ming.A simple method of balance adjustment of dual horsehead pumping unit[J].Oil-Gasfield Surface Engineering,2008,27(7):52-53.
[14]劉巨保,張宏巖.基于抽油機動力學仿真的轉矩法調平衡[J].大慶石油學院學報,2006,30(6):53-56.
LIU Jubao,ZHANG Hongyan.Torque method for adjusting balance based on dynamic simulation of the pumping unit[J].Journal of Daqing Petroleum Institute,2006,30(6):53-56.
[15]尹強,羅煉剛,陳廣曄,等.抽油機井功率平衡技術探討[J].油氣田地面工程,2009,28(5):52-53.
YIN Qiang,LUO Liangang,CHEN Guangye,et al.Discussion on power balance technology for pumping well[J].Oil-Gasfield Surface Engineering,2009,28(5):52-53.
[16]張琪,吳曉東.抽油井計算機診斷技術及其應用[J].華東石油學院學報,1984,8(2):144-159.
ZHANG Qi,WU Xiaodong.Pumping well diagnostic technique and its application[J].Journal of East China Petroleum Institute,1984,8(2):144-159.
[17]張琪,趙長祿.抽油機扭矩曲線的應用[J].石油礦場機械,1984,13(1):22-28,63.
ZHANG Qi,ZHAO Changlu.Application of torque curves of the pumping unit[J].Oil Field Equipment,1984,13(1):22-28,63.
[18]劉益江,張學臣,李偉,等.抽油井示功圖綜合解釋[J].油氣田地面工程,2007,26(8):3-5.
LIU Yijiang,ZHANG Xuechen,LI Wei,et al.The comprehensive interpretation technology for the diagnostics of rod pumping systems[J].Oil-Gasfield Surface Engineering,2007,26(8):3-5.
[19]梅啟太,徐文倬.用示功圖扭矩分析法確定抽油機平衡塊位置[J].油氣田地面工程,1991,10(3):8-10.
MEI Qitai,XU Wenzhuo.Adjustment of counter balance of pumping unit by using torque curves of the pumping unit[J].Oil-Gasfield Surface Engineering,1991,10(3):8-10.
[20]史鵬飛,崔麗巖,張彥彬,等.功率法調整抽油機平衡方法初探[J].油氣井測試,2003,12(6):51-53,56.
SHI Pengfei,CUI Liyan,ZHANG Yanbin,et al.An brief of balance way for adjusting pumping unit by power method[J].Well Testing,2003,12(6):51-53,56.
[21]吳曉東,張琪.抽油機可調相位角平衡裝置的設計[J].石油大學學報(自然科學版),1991,15(4):21-26.
WU Xiaodong,ZHANG Qi.Design of a balance device with adjustable phase angle for beam unit[J].Journal of the University of Petroleum,China(Edition of Natural Science),1991,15(4):21-26.
[編輯劉文臣]
A New Model for Calculating the Ideal Beam Counterbalance Weight for a Pumping Unit
CEN Xueqi, WU Xiaodong, WANG Lei, ZHENG Lei, GE Lei
(KeyLaboratoryforPetroleumEngineeringoftheMinistryofEducation,ChinaUniversityofPetroleum(Beijing),Beijing, 102249,China)
Abstract:In order to calculate the beam counterbalance adjustment weight accurately and ensure the safe and energy-efficient operation of beam pumping units, it is necessary to conduct research on the beam counterbalance weight adjustment model for beam pumping units. This paper presents the results of an analysis of the quick-return characteristics of beam pumping units. Results indicated that the running time of upstroke was not equal to that of down stroke. Further, the calculation formula for the average output power both in upstroke and downstroke of beam-balanced pumping units were proposed. Then, according to the balance principle of maintaining the equality of motor powers during upstroke and downstroke, a new calculation model for beam counterbalance weight of beam-balanced pumping units was derived by using the relationship between the counterbalance weight’s average power change and the motor’s average power change. It was shown from the case calculation that the difference of motor powers between upstroke and downstroke was quite narrow and the balance principle of the equality of motor powers during upstroke and downstroke could be more effectively satisfied when the counterbalance weight was adjusted by means of the new model. The longer the upstroke (downstroke) ran, the larger (smaller) the adjustment on the beam counterbalance weight. When the running time of upstroke and downstroke was almost equal, the new model and simplified model produced similar results. The results suggest that the beam pumping units whose upstroke running time was not equal to downstroke running time could be better balanced when the counterbalance weight was adjusted by means of the new power curve method-derived calculation model of beam counterbalance weight.
Key words:beam pumping unit;beam counterbalance weight; output power; mathematical model
中圖分類號:TE254
文獻標志碼:A
文章編號:1001-0890(2016)02-0082-05
doi:10.11911/syztjs.201602014
作者簡介:岑學齊(1985—),男,湖北黃岡人,2009年畢業于長江大學石油工程專業,2012年獲中國石油大學(北京)油氣田開發工程專業碩士學位,在讀博士研究生,主要從事采油工程與理論技術方面的研究。E-mail:cenxueqi2005@163.com。
收稿日期:2015-03-24;改回日期:2016-02-01。