亚洲免费av电影一区二区三区,日韩爱爱视频,51精品视频一区二区三区,91视频爱爱,日韩欧美在线播放视频,中文字幕少妇AV,亚洲电影中文字幕,久久久久亚洲av成人网址,久久综合视频网站,国产在线不卡免费播放

        ?

        Passenger airbag virtual design and simulation for C-NCAP frontal test of an electric vehicle*

        2014-06-09 14:44:40ChengyueJIANGHongyunLIYuanzhiHUXiLIU
        機床與液壓 2014年3期
        關鍵詞:重慶設計

        Cheng-yue JIANG,Hong-yun LI,Yuan-zhi HU,Xi LIU

        1Chongqing University of Technology,Chongqing 400050,China;2China Automotive Technology and Research Center,Tianjin 300300,China

        Passenger airbag virtual design and simulation for C-NCAP frontal test of an electric vehicle*

        Cheng-yue JIANG?1,Hong-yun LI2,Yuan-zhi HU1,Xi LIU1

        1Chongqing University of Technology,Chongqing 400050,China;2China Automotive Technology and Research Center,Tianjin 300300,China

        The latest C-NCAP covers 40%offset64 km/h test as well as 50 km/h full frontal test which proposes further requirements for the airbag system s.In this study,a passenger airbag of an electric vehicle,based on a B-class p latform,was developed in the CAE circumstance,for the purpose of the C-NCAP 5-star rating.Two types of concept passenger airbags were drawn based on the vehicle interior model,and evaluated through in-vehicle simulations.Static deployment test was conducted for in-vehicle analysis and module correlation,followed with passenger side restraint system optimizations with MADYMO simulations for the optimal set-up of the real world C-NCAP crash test.The effects of crash pulse,TTF,and dummy position were considered in simulations for the final parameter definitions.With this virtual design-validation process,the preliminary passenger airbag parameters for the crash test can be achieved more efficiently.

        Passenger airbag,Electric vehicle,Virtual design,MADYMO simulation,F(xiàn)rontal test

        1.Introduction

        The updated China New Car Assessment Program(C-NCAP)thereafter July 2012 increased its 40%load case velocity from 56 km/h to 64 km/h,while keep the full frontal crash test at50 km/h[1]. The offset frontal test specification is similar to the 64 km/h test in Euro-NCAP[2].This modification increases the difficulty for the restraint system development.The summary of the test specifications and dummy set-ups for C-NCAP(2012 edition)was shown in Table 1.

        Compared to the Internal-Combustion Engine(ICE)vehicle,the mass of Electric Vehicle(EV)increases due to the high-voltage battery compared with the fuel tank,considering maintain of cruising distance and cabin space[3].The energy absorption by body structures during the crash increases due to the increased mass of the battery.Therefore,it is essential to control the cabin deformation and the body deceleration for occupant protection in the frontal impact.The pulse of the EV is different with that of the ICE vehicle similar in size and platform,which contributes to the increases of the chest deflections for both driver and passenger side dummies[4].Besides,research indicated the increased mass would introduce more compartment intrusion,which makes it hard to achieve good occupant protection performance[5].

        In the development of this EV,the main work of vehicle structure was to ensure the safety of high voltage batteries,as well as the protection for the occupants by keep the cabin deformation.In this study,the main focus was on the development of a passenger airbag for the EV(based on a B-class platform),which contributed to the vehicle’s passive safety per-for mance and C-NCAP test final score.Due to increased mass and structure change,there were following changes for the airbag design and simulation of the EV,as shown in Table 2.

        Table 1.C-NCAP 2012 edition frontal test load cases and instructions

        Table 2.Input changes for the airbag design of the EV

        2.Airbag virtual design and simulation

        For the airbag design and following analysis,a computer aided engineering(CAE)model containing instrument panel,windscreen,and knee bolster was built-up.Considering the passenger airbag shape design,two airbag models were developed from the original airbag model(equipped in the vehicle of the same platform)with computer aided design(CAD)tool.To reduce the calculation time,the average temperature solution[6]was used to achieve the mass flow of inflator gas,see Equation 1.

        where msis mass flow rate,Ptankis the pressure,cvis the constant volume heat capacity,Ttankis inflator gas temperature,MWSis the molecular weight of species,cpis the constant pressure heat capacity,Tsis the average inflator temperature.

        The calculated mass flow and mass temperature were used for the airbag deployment simulations.Figure 1 shows one airbag concept design(case 1)and another design with optimized lower part(case 2).

        Figure 1.Comparison of the two concept airbags:case 1(left)and case 2(right)

        Compared with case 2,case 1 airbag simulation showed faster inflation process and the head-airbag contact surface was more appropriate than that of case 2.Thus,a manual sample airbag of case 1 concept was made and folded for the following in-vehicle deployment test,see Figure 2.

        Figure 2.Airbag sample(left)and its folding(right)

        The sample of case 1 passenger airbag was made by manual and deployed in the vehicle’s compartment(see Figure 3 left).The CAE analysis workwas conducted to make sure the deployment kinematic of the CAE model correlate well with that of the test(see Figure 3 right).

        Figure 3.In-vehicle airbag deployment test(left)and deployment simulation(right)

        3.C-NCAP frontal test simulations

        After defining the airbag dimensions and its folding process,the main focus of the following work was on the detailed parameter optimizations in the CAE circumstance.For the C-NACP front test simulations,parameters including the seat-belt elongation,seat-form stiffness were calculated based on the component test results.The elongation and stiffness data was used as the input of the passenger side simulation model,see Figure 4 below.

        Figure 4.Component tests for passenger side simulation

        The vehicle acceleration pulse(see Figure 5 left)and compartment intrusions from the structure crash worthiness simulation were used as the inputs for the occupant kinematics and passenger airbag simulations.As shown in Figure 5,the peak value of the EV is less than that of ICE,and the duration of the crash pulse is about90 ms in this case.

        Figure 5.Comparison of B-pillar crash pulses(left)and velocities(right)

        Based on the passenger side simulation analysis,the optimal parameters for the following frontal test were list in Table 3.

        Table 3.Optimal simulation parameters for the frontal test

        4.C-NCAP frontal test results

        The passenger airbag module’s performance was evaluated in the real world full frontal test,and it protected well at the dummy’s head,neck and chest regions.Table 4 shows the passenger side score proportion and head acceleration result.

        Table 4.Passenger injury result and head acceleration

        Besides,when comparing the occupant kinematics in both simulation and test,as shown in Figure 6,they correlate well with each other.Thus this method is beneficial in predicting occupant injury index and occupant kinematics with certain accuracy.

        Figure 6.Comparison of occupant kinematics in both simulation(left)and test(right)

        5.Conclusion

        In this paper,passenger airbag virtual design method and simulation process were presented,which resulted in good test results.Conclusions are drawn as follows:

        1)Airbag design and optimization through CAE analysis is efficient for the vehicle passive safety development,which can help identify the vehicle’s passive safety performance at early stage before test.

        2)In-vehicle airbag deployment test and simulation is essential for the airbag concept design and module kinematics analysis.

        3)For this electric vehicle,more attention should be paid on the reduction of the compartment intrusions which are critical for the occupant kinematics and final injury results.

        [1] China Automotive Technology and Research Center[Z]. C-NCAP test protocol,2012,http://www.c-ncap.org. cn/c-ncap_en/ep/2012english.pdf.

        [2] Euro NCAP.Frontal Impact Working Group-draft protocol for full width test 2015[Z],2014.

        [3] Hayata Uwai,Atsushi Isoda,et al.Development of body structure for crash safety of the newly developed electric vehicle[C].Proceeding of the 22ndInternational technical conference on the enhanced safety of vehicles,Washington,2011.

        [4] Hua Yang.Front impact simulation analysis of electric vehicle[D].Wuhan:Wuhan University of Technology,2008.

        [5] Fadi Tahan,Chung-Kyu Park,et al.The effect of reduced mass on frontal crashworthiness[C].The proceedings of the IRCOBI 2013 Conference,2013.

        [6] TNO.MADYMO Model Manual version 7.4[Z],2012.

        基于C-NCAP正面碰撞的某電動車乘員側氣囊虛擬設計及仿真*

        蔣成約?1,李紅運2,胡遠志1,劉 西1

        1.重慶理工大學,重慶 400050
        2.中國汽車技術研究中心,天津 300300

        最新的C-NCAP測試工況包含了64 km/h的偏置碰及50 km/h的全正碰,對安全氣囊的設計要求更高。基于某款從B級車平臺開發的電動車,利用虛擬設計及CAE分析設計出滿足C-NCAP碰撞5星目標要求的乘員側氣囊。通過氣囊概念設計—車內爆炸模擬—靜態展開試驗—整車碰撞仿真的研究方法,獲得整車碰撞優化配置參數,碰撞試驗結果與仿真耦合理想。此項虛擬設計采用與物理驗證相結合的方法,有助于高效地定義乘員側氣囊的設計參數。

        乘員側氣囊;電動車;虛擬設計;MADYMO仿真;正面碰撞

        U463.99

        10.3969/j.issn.1001-3881.2014.18.009

        2014-06-02

        *Project supported by the Chongqing Science and Technology Person Training Program(cstc2013kjrc-qnrc60002)

        ?Cheng-yue JIANG,PhD.E-mail:Jiangchengyue@cqut. edu.cn

        猜你喜歡
        重慶設計
        重慶客APP
        何為設計的守護之道?
        《豐收的喜悅展示設計》
        流行色(2020年1期)2020-04-28 11:16:38
        重慶人為什么愛吃花
        “逗樂坊”:徜徉相聲里的重慶味
        瞞天過?!律O(shè)計萌到家
        重慶非遺
        設計秀
        海峽姐妹(2017年7期)2017-07-31 19:08:17
        在這里看重慶
        今日重慶(2017年5期)2017-07-05 12:52:25
        有種設計叫而專
        Coco薇(2017年5期)2017-06-05 08:53:16
        亚洲色无码国产精品网站可下载| 久久av一区二区三区黑人| 99国产精品久久一区二区三区| 国产放荡对白视频在线观看| 内射精品无码中文字幕| 国产高清a| 午夜视频在线观看国产| 绝顶高潮合集videos| 少妇性l交大片| 亚洲国产精品悠悠久久琪琪| 国产三级一区二区三区在线观看| 久久99精品久久久久麻豆| 亚洲国产精品久久久久婷婷老年| 中文亚洲爆乳av无码专区| 国产三级在线观看不卡| 午夜人妻久久久久久久久| 大肉大捧一进一出好爽视色大师| 无夜精品久久久久久| 久久人妻精品免费二区| 亚洲第一狼人天堂网亚洲av| 亚洲国产成人久久一区www| 久久亚洲国产精品123区| 尤物精品国产亚洲亚洲av麻豆| 中国老熟妇506070| 婷婷成人亚洲| 国产精品一区二区三区黄片视频 | 亚洲视频在线观看青青草| 午夜国产视频一区二区三区| 啦啦啦www播放日本观看| 成黄色片视频日本秘书丝袜| 国产激情视频高清在线免费观看| 国产精品国产三级国产av品爱网 | 性色av免费网站| 正在播放国产多p交换视频| 日本不卡一区二区三区在线| 日本边添边摸边做边爱| 日韩精品中文字幕无码一区| 日本成熟妇人高潮aⅴ| 夜晚黄色福利国产精品| 欧美极品jizzhd欧美| 日本视频一区二区三区免费观看|