Shao Yali Wang Xudong Jin Baosheng

(1School of Energy and Mechanical Engineering, Nanjing Normal University, Nanjing 210023, China)(2School of Energy and Environment, Southeast University, Nanjing 210096, China )

Abstract：To study the gas-solid flow characteristics in a chemical looping combustion system integrated with a moving bed air reactor, a 3D full-loop numerical model was established using the Eulerian-Eulerian approach integrated with the kinetic theory of granular flow. The solid circulation mechanism and gas leakage performance were studied in detail. The simulation results showed that in the start-up process, the solid circulation rate first increased to approximately 5 kg/s and then dropped to approximately 1.2 kg/s; this observation was related to the dynamic control of the pressure distribution. In this system, the gas leakage between the inertial separator, upper air reactor, and lower air reactor was restrained by adjusting the pressure difference, thus obtaining optimal gas flow paths. When the pressures at the outlets of the inertial separator, upper air reactor, and lower air were 7.4, 11.0, and 14.6 kPa, respectively, the gas leakage ratio was less than 1% in the system.

Key words：chemical looping combustion; two-stage air reactor; solid circulation; gas leakage

Chemical looping combustion (CLC) has been developed as a combustion method that can realize inherent separation of carbon dioxide[1-2]. A typical CLC system mainly includes an air rector (AR) and a fuel reactor (FR). Oxygen and heat are continuously transported from the AR to the FR by an oxygen carrier (OC). The coal-direct chemical looping combustion (CDCLC) is a coal-fired CLC approach[3].

The final CDCLC configuration for future practical applications remains under exploration. In our previous studies,a CDCLC system comprising a circulating fluidized bed (CFB) FR, a counter-flow moving bed (CFMB) AR, an inertial separator, and a loop seal was built up. The results proved the feasibility of the configuration design for CDCLC[4]. Moreover, a novel two-stage AR was proposed to improve the carrying capacity of the gas flow in the AR and the power capacity of the CDCLC system. The novel AR was composed of two CFMBs connected in series, which also showed potential advantages in terms of the reaction performance and running cost.

To explore the feasibility of the improved CDCLC system with a two-stage AR, alteration of experimental apparatus would be time-consuming and expensive. With the development in numerical techniques and improved computational capacity, computational fluid dynamics (CFD) modeling has been widely adopted to study the complicated gas-solid flow behaviors[5-7]. Thus far, only a few CFD simulations have been performed on coal-fired CLC, most of which have focused on single reactors[8-9]. In practice, not all the results obtained from single reactor simulations can be directly applied to a CDCLC system, because the coupled effect between the reactors cannot be neglected.

In our previous study, a 3D full-loop numerical model was established for an improved CDCLC system with a high-flux CFB as the FR, two CFMBs connected in series as the two-stage AR, a down-comer, an inertial separator, and a loop seal[4]. To obtain deeper insights into the gas-solid flow dynamics in the system, the solid circulation process and optimization of gas flow paths were studied in detail in this work.

1 Simulation Condition

1.1 Mathematical model

The comprehensive 3D model was built based on our previous study[4]. For each phase, mass and momentum conservation equations were solved. The standard k-ε turbulence model was used to describe the turbulent gas flows. The kinetic theory of granular flow (KTGF)[10]was applied to calculate the conservation of the particle fluctuation energy, where the kinetic energy of the moving particles was expressed using the granular temperature. A detailed description of the models can be seen elsewhere[4].

1.2 Geometry and meshing

Fig.1 shows the 3D model of the improved CDCLC system.

Fig.1 Three-dimensional model of the improved CDCLC system

For the CFB FR, the inner diameter was 60 mm, and the reactor height was 5.8 m. Two identical CFMBs connected in series were adopted as the AR, and the inner diameter and reactor height were 0.418 and 0.400 m, respectively. Considering the computational accuracy and speed, the calculation domain of 638 795 cells was finally selected for this study after the grid independence test.

1.3 Numerical procedure

The pressure-based method was adopted to solve the governing equations[11]. The time step was 0.5 ms, and 20 iterations were set for each time step to ensure convergence of most time steps.

2 Results and Discussion

The particle has a diameter of 0.65 mm and a density of 2 558 kg/m3. Initially, the outlet pressures of the separator, upper CFMB of AR, and lower CFMB of AR were set to 7.4, 10.0, and 17.5 kPa, respectively.

2.1 Solid circulation mechanisms

Particle circulation would affect oxygen and heat transfer in CDCLC systems. With gas introduced to the system, solids initially packed in the system were entrained by gas and moved upwards in the FR. Subsequently, solids from the FR outlet can realize regeneration in the two-stage AR owing to effective separation of the inertial separator. Finally, through the loop seal, the solids returned to the FR. Two monitoring surfaces were set to monitor the solid circulation rates, located at the bottom section of the FR and the top of the down-comer. Fig.2 shows the comparison between the solid circulation rate fluctuations monitored at the two faces. After a computational time of approximately 2 s, particles were detected in the bottom section of the FR, indicating that the solids were gradually transported from the down-comer to the FR. The solid circulation rate increased to a maximum value of approximately 5 kg/s and then gradually decreased because of the dynamic pressure balance. The solid circulation rate fluctuated at approximately 1.2 kg/s steadily when solid circulation was achieved. The solid circulation rates monitored at the down-comer presented similar trends as those monitored at the bottom of the FR. The close solid circulation rate of 1.2 kg/s at the steady state proved the effective separation of solids to the down-comer. However, there was a time delay between the two curves, which was due to the movement of particles from the FR to the down-comer.

Fig.2 Comparison between solid circulation rate fluctuations monitored at the bottom of FR and the top of down-comer

2.2 Regulation of gas flow paths

Owing to the addition of another CFMB as the AR, the complexity of gas flow paths and the risk of gas leakage between different components were inevitably increased in the improved CDCLC system. Considering the disadvantages, it is essential to restrain gas leakage between the different components in the improved CDCLC system.

The pressure gradient was the fundamental cause of the gas leakage, and hence the leak ratios could be minimized through the pressure regulation.Two parametersYs,auandYau,sare used to represent the fraction of the FR gas flowing out from the upper CFMB outlet and the fraction of upper CFMB inlet gas exiting from the separator outlet. Similarly, gas leakage between the two CFMBs could be defined as the fraction of the upper CFMB inlet gas passing into the lower CFMB, and the fraction of lower CFMB inlet gas passing into the upper CFMB, which could be expressed by two parametersYau,alandYal,au, respectively.

2.2.1 Effects of pressure difference on gas leakage performance

The separator outlet pressure and upper CFMB AR outlet pressure were set to 7.4 and 17.5 kPa, respectively. The pressure difference ΔP1between the inertial separator and upper CFMB outlet was changed from 2.1 to 5.1 kPa. Fig.3(a) shows the distributions of the gas leakage ratios (Ys,au,Yau,s). Higher ΔP1could better restrain the FR gas flowing to the upper CFMB. There was almost no gas leaking from the upper CFMB to the separator when ΔP1ranged from 2.1 to 3.6 kPa; however, a further increase in ΔP1could lead to more upper CFMB inlet gas flowing to the separator. As it was difficult to keep the two gas leakage ratios to zero at the same time, and a little FR gas flowing into the upper CFMB was allowed, the optimal pressure difference ΔP1of 3.6 kPa was finally chosen for the system, which could make sure that no upper CFMB gas flow into the separator, and FR gas leakage fractionYs,auwas less than 1%.

To determine the optimal pressure difference ΔP2between the upper CFMB outlet and lower CFMB outlet, pressure difference ΔP1was kept to 3.6 kPa to minimize the gas leakage between the separator and upper CFMB. Fig.3(b) shows the distribution of the gas leakage ratios (Yau,al,Yal,au) with ΔP2ranging from 1.5 to 4.5 kPa.Yau,aldecreased with increasing ΔP2, demonstrating that a higher ΔP2was helpful in preventing the upper CFMB inlet gas from flowing to the lower CFMB. The gas leakage from the upper CFMB to the lower CFMB disappeared, when ΔP2increased to 4.0 kPa. Meanwhile, with the increase of ΔP2,Yal,auinitially kept at near-zero and then gradually increased. The critical value occurred at ΔP2=3.5 kPa. To minimize the gas leakage between the two CFMBs, the pressure difference ΔP2of 3.6 kPa at the intersection of two curves was finally selected as the optimal ΔP2for the system, which could ensure that the gas leakage ratios (Yau,al,Yal,au) were both less than 1%.

2.2.2 Gas distributions at three outlets

To verify the feasibility of the optimal pressure difference in minimizing the gas leakage, an improved CDCLC system was operated by setting the separator outlet pressurePs, the upper CFMB outlet pressure and the lower CFMB outlet pressure to 7.4, 11.0 and 14.6 kPa, respectively (ΔP1=3.6 kPa and ΔP2=3.6 kPa). Fig.4 shows the gas distributions in three outlets of the improved CDCLC system. In the separator outlet, the gases included the FR inlet gas accounting for the major proportion of 84.2% and the loop seal inlet gas taking up 15.8%, indicating that there was no leaking gas from the AR. As for the upper CFMB outlet, the gas from its own inlet occupied the highest percentage of 94.6%, and the total leaking gas just took up a small proportion, and hence, the gas leakage into the upper CFMB had been successfully restrained. In the lower CFMB, 82.3% of the outlet gases were from its own inlet. The gas leaking from the upper CFMB just occupied 0.4%, demonstrating minimization of the gas leakage between two CFMBs. Thus, the optimal AR outlet pressures were able to effectively restrain the gas leakage between different components of the CDCLC system, which was beneficial for achieving high CO2capture efficiency and stable gas-solids flow states.

3 Conclusions

1) During the start-up process, the solid circulation rate first increased to approximately 5 kg/s and then decreased to approximately 1.2 kg/s, and the trend was related to the dynamic control of the pressure distribution.

2) When the pressure difference between the inertial separator outlet and the upper CFMB outlet (ΔP1) and the pressure difference between the upper CFMB outlet and lower CFMB outlet (ΔP2) were both adjusted to 3.6 kPa, the gas leakage between the inertial separator and two CFMBs were effectively restrained, with the gas leakage ratios being less than 1% under the involved conditions. This can be beneficial for realizing a high CO2capture efficiency and a stable movement of the solids in the system.

3) With the separator outlet pressure, upper CFMB outlet pressure and lower CFMB outlet pressure set to 7.4, 11.0, and 14.6 kPa, respectively, reasonable gas flow paths were achieved. The gases at the separator outlet included 84.2% FR gas and 15.8% loop seal gas; 94.6% of the gases at the upper CFMB outlet were from its own inlet and 82.3% of the gases at the lower CFMB outlet were from its own inlet.