亚洲免费av电影一区二区三区,日韩爱爱视频,51精品视频一区二区三区,91视频爱爱,日韩欧美在线播放视频,中文字幕少妇AV,亚洲电影中文字幕,久久久久亚洲av成人网址,久久综合视频网站,国产在线不卡免费播放

        ?

        Moisture Absorption and Desorption in an Ionomer-Based Encapsulant:A Type of Self-Breathing Encapsulant for CIGS Thin-Film PV Modules

        2020-05-11 01:19:44MiaoYangRaymundSchfflerTobiasRepmannKayOrgassa
        Engineering 2020年12期

        Miao Yang, Raymund Sch?ffler, Tobias Repmann, Kay Orgassa

        NICE Solar Energy GmbH, Schwaebisch Hall 74523, Germany

        Keywords:

        Ionomer

        Encapsulant

        Moisture absorption and desorption

        Cu(In,Ga)Se2 photovoltaic module

        ABSTRACT As an alternative to conventional encapsulation concepts for a double glass photovoltaic(PV)module,we introduce an innovative ionomer-based multi-layer encapsulant, by which the application of additional edge sealing to prevent moisture penetration is not required. The spontaneous moisture absorption and desorption of this encapsulant and its raw materials, poly(ethylene-co-acrylic acid) and an ionomer, are analyzed under different climatic conditions in this work. The relative air humidity is thermodynamically the driving force for these inverse processes and determines the corresponding equilibrium moisture content (EMC). Higher air humidity results in a larger EMC. The homogenization of the absorbed water molecules is a diffusion-controlled process, in which temperature plays a dominant role. Nevertheless, the diffusion coefficient at a higher temperature is still relatively low.Hence, under normal climatic conditions for the application of PV modules, we believe that the investigated ionomer-based encapsulant can ‘‘breathe” the humidity: During the day, when there is higher relative humidity, it ‘‘inhales” (absorbs) moisture and restrains it within the outer edge of the module; then at night, when there is a lower relative humidity, it ‘‘exhales” (desorbs) the moisture. In this way, the encapsulant protects the cell from moisture ingress.

        1. Introduction

        Encapsulants, which are chemically stable, compatible with cells,and exhibit high resistance against atmospheric gases,pollutants, radiation, mechanical stress, and so forth, are of great interest for photovoltaic (PV) module manufacturing, especially in terms of reliability [1-5]. Polymer film based on ethylene-vinyl acetate copolymer (EVA) has hitherto been the most widely used encapsulant in single-glass/backsheet c-Si modules [6]. However,many results from research and applications indicate that EVA’s potential to release acetic acid under exposure to atmospheric water and/or ultraviolet radiation, along with related problems in reliability,restrict its application,especially for double-glass applications [7,8]. For building-integrated photovoltaic (BIPV) applications, the requirements for the mechanical stability and safety of PV modules are more essential. As a well-known thermoplastic interlayer for laminated safety glass, polyvinyl butyral (PVB),which has higher resistance against mechanical load,has been successfully implemented in BIPVs[9].The most critical disadvantage of PVB is its high sensitivity to hydrolysis,followed by a high water uptake, which results in a significant decrease of its adhesion to glass [10] and the formation of haze [11]. In recent years, there has been increasing demand for an advanced encapsulation solution based on polyolefin elastomers (POE) arising from PV module manufactures [12]—especially for double-glass c-Si modules and thin-film modules. Unfortunately, the water vapor transmission rate (WVTR) of POE, which is about a few grams per square meter per day according to technical data sheets, is not low enough. The edges of PV modules encapsulated with any of the abovementioned materials must therefore be additionally well sealed against moisture ingress[13,14].Through our elaborate investigations and perennial application experiences, we report an ionomer-based self-breathing encapsulant film with no edge sealing for our Cu(In,Ga)Se2(CIGS) thin-film PV modules.

        2. Material and methods

        The investigated encapsulation film, which has a multilayer structure consisting of poly(ethylene-co-acrylic acid) (EAA) and thermoplastic ionomer (metal-ion-neutralized EAA), is a commercial product provided by our partner company.It has a thickness of 0.7 mm, an EAA/ionomer volume ratio of 1:2, and a melting point of 98 °C.

        In order to investigate their moisture absorption, the encapsulant samples and their corresponding raw material pellet samples were respectively placed in glass bottles and dried in a vacuum dryer (Goldbrunn 450, GOLDBRUNN, Germany)under about 2 kPa at 80°C for one week.Although a certain amount of residual water should still exist,we define the samples after this treatment as dry samples in this paper.Subsequently,the samples were respectively stored in a climate chamber (VCL 4010, V?tsch Industrietechnik GmbH,Germany)for moisture absorption.Under every set of temperature and relative air humidity(details provided in Section 3.1),one encapsulant sample(~2 g),one EAA pellet sample(~10 g),and one ionomer pellet sample(~10 g) were kept in the chamber until their equilibrium moisture contents(EMCs)were achieved.In order to observe the moisture desorption, samples with saturated moisture contents were stored in a climate housing,where the temperature was kept at 22 °C and the relative air humidity was maintained between 8%and 10%,until a new EMC was reached.

        Moisture absorption and desorption in the ionomer encapsulant samples were monitored by an analytical scale (ABT120-5DM,KERN GmbH, Germany). During moisture absorption under given conditions in the climate chamber, the samples were taken out of the chamber after a certain time interval and weighed using a scale as quickly as possible. After that, the samples were placed back into the climate chamber for further absorption.During moisture desorption, the encapsulant samples were weighed in situ in the climate housing. The moisture content M is therefore a function of the storage duration t and is proportional to the increase in sample weight ΔW t( ):

        where W 0( ) and W t( ) represent the weight of the dry sample and its value at t, respectively.

        3. Results and discussion

        3.1. Moisture absorption

        Fig. 1 illustrates the time-dependent moisture absorptions of the ionomer-based encapsulant samples and their pellet raw materials under three climatic conditions: 30 °C and 70% relative humidity (RH; corresponding to an absolute humidity of 21.2 g?m-3); 50 °C and 26% RH (21.5 g?m-3); and 50 °C and 70%RH (57.9 g?m-3). These can be well described using a simplified solution of the second Fick equation[15]with the following form:

        where M∞is the EMC and K is a constant that contains the diffusion coefficient and a geometric factor.

        Since the scale of the encapsulant film thickness h is much smaller than its area, we may consider the film as an infinitely large plate; thus, the moisture only diffuses perpendicularly through the film surface into the film.The constant K is therefore a quotient of the diffusion coefficient D against 4h2[15].Due to the multilayer structure,we further developed Eq.(2)for our case as follows:

        Fig. 1. Moisture absorption by EAA pellets, ionomer pellets, and ionomer-based encapsulant at (a) 30 °C and 70% RH (21.2 g?m-3); (b) 50 °C and 26% RH(21.5 g?m-3);and(c)50°C and 70%RH(57.9 g?m-3).The blue and red dashed lines are fitting curves according to Eq. (2), and the black dashed line is a curve-fit according to Eq. (3).

        where xEAAand xionomer=1-xEAArepresent the content of the EAA and the ionomer,respectively.Using Eqs.(1)and(2),we graphically determined the key parameters to describe the moisture absorption process in both the raw materials and the encapsulant, as listed in Tables 1 and 2, respectively.

        The moisture absorption in the investigated encapsulant is due to the fact that the COO-Me+groups in the ionomer are highly polar, with a strong hydrophilic character. Kutsumizu et al. [16]concluded by analyzing sodium-neutralized EAA that each COO-Na+ion pair is able to absorb three water molecules in its vicinity to build a tightly bonded primary hydration shell. As absorption proceeds, the excess water molecules locate around the primary hydration shell.Based on our results,shown in Table 1,we confirm that the polar ionomer is able to absorb more water molecules than the less polar EAA. For the same reason, themobility of the water molecules trapped by the COO-Me+ion pair in the ionomer is significantly suppressed, resulting in a much smaller diffusion coefficient (corresponding to a lower WVTR). In 2010,Kempe et al.[14]experimentally characterized the moisture permeation in laminated glasses with different encapsulants.Considering the moisture permeation as a one-dimensional diffusion-controlled process, they determined the diffusion coefficient of water in their investigated ionomer at 85 °C and 85%RH to be 1.25×10-4mm2?s-1(this result is calculated according to the data in Ref. [14]), which is more than one magnitude smaller than the values in EVA (4.01 × 10-3mm2?s-1) and PVB(1.74 × 10-3mm2?s-1), and is in reasonable agreement with our results in Table 2.

        Table 1 EMC M∞and constant K of EAA and ionomer pellets, and the adjusted R2 obtained by fitting the experimental results illustrated in Figs. 1(a)-(c).

        Table 2 EMC of each of the components, MEAA,∞and Mionomer,∞, in the encapsulation film; diffusion coefficient of the water molecules DEAA and Dionomer; and the adjusted R2 obtained by fitting the experimental results illustrated in Figs. 1(a)-(c).

        The establishment of thermodynamic equilibrium is preceded by the homogenization of the absorbed water molecules in the material, which is a diffusion-controlled process. Under constant relative humidity, a higher temperature increases the diffusion coefficient of the water molecules, causing the absorption or desorption to reach its equilibrium faster (results shown in Figs. 1(a)-(c)).

        3.2. Moisture desorption

        As mentioned above, an encapsulant with saturated moisture content can release the absorbed water molecules if the air humidity of its surroundings decreases.This phenomenon is clearly indicated by the results shown in Fig. 2. As can be seen, although the EMC in the samples is initially unequal, the temporal developments of the moisture content are similar. This means that the kinetics of moisture desorption, and therefore the rate constant of desorption kdes, are independent of the amount of adsorbed water molecules.Hence,we describe this kind of water desorption by using the Kissinger analysis for the first-order homogeneous reaction [17] with the following form:

        3.3. Absorption isotherm

        Fig. 3 schematically describes the influence of RH on the moisture content at equilibrium M∞in the ionomer pellet samples according to our current experimental results.The red dashed line is a guideline for the eye, based on the Hailwood-Horrobin equation [18]:

        Fig. 2. Moisture desorption of the ionomer-based encapsulant, whose moisture content was saturated at room temperature under two different air humidities.Moisture desorption was realized by storing these samples at room temperature with significantly lower air humidity.The normalized moisture contents,according to the saturated value, are plotted against the storage duration and fitted with a black dashed curve using Eq. (4).

        Fig. 3. Sorption isotherm of water molecules for ionomer pellets at 50 °C. The results at 26%RH and 70%RH are graphically determined and listed in Table 1.The result at 7.5%RH was calculated through our previous work(not published).Results are fitted with a red dashed curve using Eq. (5).

        A, B, and C represent the temperature-related constants,respectively.

        Although a more accurate fitting is lacking, the red dashed line in Fig. 3, with A = 0.5278, B = 2.6516, and C = 4.0345, indicates a significant increase of EMC in the ionomer if the relative air humidity is greater than 60%.The line further serves as a guideline for the manufacture of both the encapsulant and the module, in order to control air humidity during production.

        3.4. Self-breathing encapsulant

        In regard to the spontaneous moisture absorption and desorption, as discussed above, it is reasonable to consider the investigated ionomer-based encapsulant as a self-breathing material that depends on air humidity: During the daytime, when there is comparative higher relative air humidity, the encapsulant absorbs moisture. Thanks to the low diffusion coefficient, as listed in Table 2, most of the absorbed water molecules are concentrated on the very outer edge of the PV module. During the night, the lower air humidity reverses the direction of the thermodynamic process;thus,the encapsulant releases moisture.Therefore,as long as the edge area is wide enough(which is also essential for insulation distance),moisture can scarcely reach the cells under conventional application conditions, and no edge sealing is required.

        Compared with other conventional moisture-absorbing encapsulants such as EVA and PVB, we emphasize that the selfbreathing function of the ionomer-based encapsulant exhibits two practical and essential advantages: ①No hydrolysis reaction exists, and moisture absorption and desorption in the ionomerbased encapsutant are completely reversible; and ②the diffusion coefficient of water in the ionomer is significantly lower than that in EVA and PVB, as discussed in Section 3.1. Although water diffusion in EAA is comparatively faster,the EMC of EAA,which is about 0.02%, is negligible.Hence, as the presented encapsulant is a combination of these two components,the water penetration depth in it will be much smaller than that in EVA and PVB under the same conditions. According to the results in Ref. [14], 10 h is roughly sufficient for water molecules to penetrate a distance of 10 mm in EVA and PVB at 85°C and 85%RH.As certificated by TüV Rheinland, we report that, after a standard 1000 h of damp heat treatment, the power degradation of our CIGS modules, which have an edge width of 8.4 mm and use the ionomer-based encapsulant,is less than 5%, which fulfills the regulation of the international electrotechnical commission standards (IEC 61730).

        4. Conclusions

        In the present work, we have introduced a promising ionomerbased encapsulant, which is able to spontaneously absorb and/or desorb moisture. This process is thermodynamically driven by the RH of the environment. Furthermore, since the temperaturedepended diffusion coefficient of water molecules is relatively low due to the polar nature of the COO-Me+groups in the ionomer,the encapsulant is able to‘‘inhale”moisture when the air humidity is high, and ‘‘exhale” it when the air humidity decreases, without letting the moisture ingress into the cells.

        Acknowledgements

        The support from our partner company in providing the ionomer-based encapsulant samples and the corresponding raw materials as well as the permission for material analysis is fruitfully acknowledged. Special thanks are due to Dr. Gernot Oreski from Polymer Competence Center Leoben GmbH (Austra)for the helpful discussions.

        Compliance with ethics guidelines

        Miao Yang, Raymund Sch?ffler, Tobias Repmann, and Kay Orgassa declare that they have no conflict of interest or financial conflicts to disclose.

        99riav精品国产| 午夜福利一区二区三区在线观看| 国产精品_国产精品_k频道 | 日韩欧美国产自由二区| 久久中文字幕乱码免费| 日本一本草久国产欧美日韩| 亚洲24小时免费视频| av影院手机在线观看| 中文字幕亚洲无线码在线一区| 亚洲精品无码不卡在线播放he| 国产精品久久1024| 国产一区二区一级黄色片| 国产极品大秀在线性色| 国产桃色一区二区三区| 久久久久免费精品国产| 精品亚洲成在人线av无码| 国产精品-区区久久久狼| 国产精品久久国产三级国电话系列| 91久国产在线观看| 99久久精品国产91| 专干老熟女视频在线观看| 亚洲最大中文字幕无码网站| 久久综合一本中文字幕| 国产精品精品国产色婷婷| 国产成人小视频| 欧美婷婷六月丁香综合色| 亚洲女同成av人片在线观看| 亚洲视频在线观看青青草| 水蜜桃网站视频在线观看| 无码小电影在线观看网站免费| 乌克兰粉嫩xxx极品hd| 国产2021精品视频免费播放| 久久精品国产亚洲av调教| 日本视频一区二区三区在线| 亚洲av无码久久| 亚洲精品国产综合一线久久| 久久免费精品视频老逼| 蜜芽亚洲av无码精品色午夜| 国产成人无码免费网站| 精品国产福利久久久| 男女男在线精品免费观看|