2014年6期
刊物介紹
本刊以紡織、合成纖維、服裝等學科為特色，兼顧相關學科的學術刊物，主要刊載本校師生員工的科技論文，同時也刊載校外、海外的科研論文。
Journal of Donghua University(English Edition)
- Optimization of Quality Consistency Problem of Electromechanical Component due to Manufacturing Uncertainties with a Novel Tolerance Design Method
- Integrated Robust Design Method Based on Maximum Tolerance Region
- Reliability Analysis Based on a Nonlinear Fatigue Damage Accumulation Model
- Periodical Inspections and Delay Replacement Model Based on Age Preventive Replacement Policy
- Effect of Starch Dodecenylsuccinylation on the Adhesion and Film Properties of Dodecenylsuccinylated Starch for Polyester Warp Sizing
- Reliability Analysis of Lithography Wafer Stage Based on Fuzzy Bayesian Networks
- Two Probability Plots of the Three-Parameter Lognormal Distribution
- Machine Tool Fault Information Management System Software Development
- Interval Fault Tree Analysis of Excavator Variable-Frequency Speed Control System
- Reliability Estimation of Aviation Pyrotechnics System Based on Mixed Beta Distribution
- Load Dependent Series-Parallel Systems with Common Bus Performance Sharing Mechanism
- Combinatorial Optimization Based Analog Circuit Fault Diagnosis with Back Propagation Neural Network
- Reliability Allocation of Large Mining Excavator Electrical System Based on the Entropy Method with Failure and Maintenance Data
- Deployment Reliability Test and Assessment for Landing Gear of Chang’E-3 Probe
- Reliability Analysis of Hydraulic Transmission Oil Supply System of Power-Shift Steering Transmission with GO Methodology
- Importance Analysis of a Multi-state System Based on Direct Partial Logic Derivatives and Multi-valued Decision Diagrams
- Methods for Reliability Assessment under Irregular Time-Varying-Stress Degradation Testing
- Identification of the Credit Guarantee Network of Steel Trade Enterprises in China
- Immune Clone Maximum Likelihood Estimation of Improved Non-homogeneous Poisson Process Model Parameters
- Condition-Based Maintenance Decision-Making for Equipment
- Global Mission Sensitivity Study for Phased Mission System with Analysis of Variance Method
- Settlement Prediction of Dredger Fill with the Optimal Combination Model
- Yarn Quality Prediction and Diagnosis Based on Rough Set and Knowledge-Based Artificial Neural Network
- Equipment Maintenance Material Demand Forecasting Based on Gray-Markov Model
- Carbon Emission Modeling and Analysis in Manufacturing Process for Numerical Control Machine Tools
- Based Machinery Condition Prediction Based on Support Vector Machine Model with Wavelet Transform
- Failure Modes of Machining Center in Test Run
- Reliability Analysis of Wind Turbine Gearbox Based on the Optimal Confidence Limit Method
- Rapid Evaluation for Feed-axis Lubrication Condition Based on Soft Sensor
- Stress-Strength Structural Reliability Model with a Stochastic Strength Aging Deterioration Process
- Multi-objective Particle Swarm Optimization Algorithm Based on Performance and Reliability of Discrete System Resources Configuration
- Reliability Based Design Optimization of Aero-Engine Spindle Ball Bearings
- Selection of Support System Type with Dectecting Mismatches between Traffic Situation and Driver Behavior
- Electric Multiple Unit Bogie Maintainability Allocation with Interval Analysis and Fuzzy Evaluation Method
- New Approach to Calculate the Unavailability of Identical Spares in Cold Spare Configuration
- Revised Fault Free Analysis Method for Reliability Evaluation of Smart Grids
- Coupled Faults Analysis and Evaluation Methods Based on Cellular Automata
- Novel Fault Detection Optimization Algorithm for Single Event Effect System Based on Multi-information Entropy Fusion
- Efficient Method for Accelerated Reliability Qualification Testing
- Reliability Study on the Risk Precontrol Management System of Coal Mines Safety
- Optimal Extended Warranty Policies under Different Maintenance Options
- Risk Assessment, Management and Application in Nuclear Power Plant Operation